Metso Process Technology and Innovation (PTI) reported a recent mine-to-mill Process Integration and Optimization (PIO) project at the Newmont Ahafo mine in Ghana resulted in a significant increase in mill throughput without capital investment. This was achieved by reviewing the current operating conditions, identifying inefficiencies and then implementing PTI’s recommended changes in drill and blast, crushing and grinding practices.

Ahafo is currently mining a number of open-pits with the majority of ore coming from the Apensu and Awonsu working areas. A blend of both primary and oxide ore is fed to the mill to balance the head grade and recovery in the leach circuit. Ahafo operates a 54 x 75-in. gyratory crusher for primary ore and a toothed roll sizer for oxide ore. This is followed by an SABC circuit comprising a 34 x 16.4-ft, 13-MW SAG mill in closed circuit with two 600-kW pebble crushers. SAG milling is followed by a 24 x 39-ft, 13-MW ball mill in closed circuit with a cluster of 26-in. cyclones. After classification, the milling product is thickened and the overflow is fed to carbon-in-leach tanks.

A PIO project normally consists of a number of site visits spaced over a few months. The first site visit is to establish current operating practices, initiate rock characterization and collect measurements of blast fragmentation and mill performance during a series of plant trials or sampling surveys. This is followed by modeling and simulation studies to determine how to best exploit hidden inefficiencies. These recommendations are then followed by further site visits to implement the changes, monitor the results and ensure the improvements are maintained over time.

Metso noted that in a PIO project, it is important the material being surveyed in the plant is the same that has been characterized and closely studied from the audited blast. This requires ore tracking. PTI has developed a radio frequency-based material tracking system, called SmartTag, that allows parcels of ore to be followed from the mine through the crusher, intermediate stockpiles and finally into the grinding circuit. The RFID tags are detected as they pass near antennae that are typically installed on conveyor belts. Being passive, the tags don’t have a power source and therefore can last an indefinite period and reside in stockpiles for many years if necessary. Detecting tags before and after stockpiles can provide a reliable indication of their active residence time.

Two full grinding circuit surveys were performed at Ahafo as part of the initial benchmarking phase of the PIO project. Both surveys were completed while processing material from a particular blast, tracked using SmartTags. At Ahafo, each blast is mined in two benches (or flitches) and the first survey was conducted on the top bench while the second was done on the bottom bench. This would clearly show the effect of the coarser, top bench fragmentation on mill throughput.

At the end of each survey, the SAG mill was crash-stopped and the rock and ball loads were measured. The survey sample sizing data were then used for mass balancing and calibration of crushing and grinding circuit steady-state models.

Blast design changes were modeled and the predicted run-of-mine fragmentation was input to the grinding circuit model during a number of simulations to achieve different increases in mill throughput. The blast patterns were designed to increase the amount of ultra fines generated during blasting that cannot be created through conventional crushing. These very fine particles are beneficial to both semi-autogenous and fully autogenous milling as they pass through the mill and onto the ball mill circuit. Once the primary mill restriction has been alleviated, issues around the ball mill will need to be addressed as this can become the bottleneck. For the Ahafo project, the blast designs recommended by PTI aimed to increase the amount of ultra fines from 18% to 24%.

As well as blast design changes, the performance of the crushing and grinding circuits was reviewed during the PIO project. It was recommended Ahafo measure the primary crusher closed-side-setting once a week and maintain it between 5- and 6-in., based on operating power draw. This would ensure the additional fines generated in blasting would be supplemented with good topsize control by the primary crusher.

Other PTI recommendations included operation of the pebble crusher, SAG mill rock and ball load monitoring, ball mill media size and cyclone conditions.

Following implementation of PTI’s recommendations, Metso said plant trials conducted in the last quarter of 2010 showed a significant increase in mill throughput compared with the benchmark surveys on the same material earlier in the year. Metallurgical hardness tests showed the validation trial mill feed was even harder than the benchmarked ore.

Resource Center Whitepapers, Videos, Case Studies

Let's stay in touch!

All of the latest mining news and our digital edition sent to your inbox once a week.

We'll never share your email address, and you can opt out at any time, we promise.